New condenser and coil
A matched condenser and evaporator coil sized to your home by ACCA Manual J load calculation. We install AHRI-matched pairs so your warranty stays valid and the system performs at its rated efficiency.
When your old condenser quits for good, ac replacement azusa CA is the fastest route back to a cool house. Azusa Breeze HVAC swaps out failed systems for properly sized, code-correct units across Los Angeles County. We handle the load calculation, the line set, the thermostat, and the permit so you get one clean job instead of five contractors pointing fingers at each other.

AC replacement means pulling the old condenser, evaporator coil, and often the line set, then installing a new matched system sized to your home. It is not a swap-and-go job. We run an ACCA Manual J load calculation, check duct static pressure, and verify the electrical disconnect and breaker can carry the new unit. Every joint gets pressure-tested with nitrogen, evacuated with a vacuum pump and micron gauge, then charged by weight on a refrigerant scale. Done right, the system runs quieter, holds its charge, and cools the whole house instead of one room.
Most azusa ac replacement service calls we run start the same way: a 15-year-old unit that survived one too many 105-degree afternoons in the Foothills, a compressor that finally locked up, or an R-22 system nobody can legally recharge. If you are weighing when to replace ac unit in azusa California versus patching it again, the math usually tips toward replacement once the repair passes a third of the cost of a new system. We give you both numbers before you decide.
Every ac replacement azusa CA job we quote includes the equipment, labor, permit, and the parts most contractors charge extra for. Here is what you get, and what we treat as an add-on if your home needs it.
A matched condenser and evaporator coil sized to your home by ACCA Manual J load calculation. We install AHRI-matched pairs so your warranty stays valid and the system performs at its rated efficiency.
New copper line set sized to the equipment, brazed under nitrogen flow, and pressure-tested. Reusing old line sets on a new system is a common shortcut that leads to leaks and charge loss within a few years.
A new thermostat installed and wired, including a C-wire run if your old system did not have one. We can upgrade to a Nest or Ecobee smart thermostat at the same time if you want scheduling and remote control.
We pull the mechanical permit and build to Title 24 Compliance so your final inspection passes. Unpermitted HVAC work can complicate a home sale and void manufacturer warranties.
The old condenser, coil, and any removed ductwork leave with us. We cover floors, protect walls, and leave the mechanical closet cleaner than we found it.
Vacuum to under 500 microns, charge by weight on a refrigerant scale, and verify amp draw with a clamp meter. We record supply and return temperatures and walk you through the results.
We measure every room, check window orientation, insulation, and duct sizing, then run an ACCA Manual J load calculation. This tells us the exact tonnage your house needs. Oversized units short cycle and leave humidity behind, so we size it right the first time. Takes about 60 to 90 minutes on site.
You get two or three system options with real numbers: equipment cost, efficiency rating, warranty length, and the estimated monthly difference. We walk through Carrier, Trane, Lennox, Goodman, Rheem, and Daikin options so you can compare apples to apples. No pressure, no same-day-only discount games.
A two-man crew handles most residential swaps in one day, 6 to 10 hours. We set the pad, run the copper line set, braze with a torch kit under nitrogen, install the PVC condensate drain line with proper slope, and wire the thermostat. Floors get covered, and the old equipment leaves with us.
We pull a deep vacuum with the vacuum pump and confirm it holds under 500 microns on the micron gauge. Then we charge refrigerant by weight using a refrigerant scale, not by guessing at gauge pressures. A clamp meter and multimeter confirm amp draw on the compressor and blower motor before we call it done.
We run the system through a full cooling cycle, check supply and return temperatures with a psychrometer, and show you the thermostat settings. You get the permit paperwork, warranty registration, and filter sizes written down. If anything reads off in the first 30 days, we come back at no charge.
We measure every room, check window orientation, insulation, and duct sizing, then run an ACCA Manual J load calculation. This tells us the exact tonnage your house needs. Oversized units short cycle and leave humidity behind, so we size it right the first time. Takes about 60 to 90 minutes on site.
Reads high and low side pressures during charging and diagnostics. We use it alongside a refrigerant scale so the charge is set by weight, not by guesswork.
Pulls a deep vacuum on the line set and confirms it holds under 500 microns. Moisture left in the system destroys compressors, so this step is not optional.
Recovers old refrigerant legally and weighs in the exact charge for the new system. Required under EPA Section 608 rules and essential for correct performance.
Braze copper line sets under nitrogen flow and form clean flares on mini-split connections. Poor brazing is a leading cause of refrigerant leaks.
Verify voltage, continuity, and amp draw on the compressor, blower motor, and control board. This is how we confirm the system is running within spec before we leave.
Measures wet-bulb and dry-bulb temperatures at supply and return. It tells us whether the system is actually removing heat and humidity, not just blowing air.

A 16-year-old 4-ton system in the Azusa Foothills lost its compressor during a 106-degree week. The house sat at 93 degrees inside, and two prior repair calls that summer had already cost the homeowner over $1,400.
After: We installed a matched 4-ton 16-SEER2 Rheem system with a new copper line set and smart thermostat. Indoor temperature dropped to 74 degrees within two hours of startup, and the system held 72 to 74 through the rest of the summer.
Book this service →
A home near Azusa Pacific University ran a 5-ton system in a house that needed 3.5 tons. It short cycled every four minutes, never removed humidity, and pushed summer electric bills past $400.
After: We installed a right-sized 3.5-ton 16-SEER2 Carrier system, sealed the duct plenums with mastic, and added a Nest thermostat. Runtime stabilized, humidity dropped, and the first full summer bill came in roughly 28 percent lower.
Book this service →
A homeowner on the Citrus Avenue Corridor was selling a 1978 house with an R-22 system that had never been permitted. The buyer's inspector flagged it, and the sale stalled on the HVAC objection.
After: We replaced the system with a new R-410A unit, pulled the mechanical permit, and built to Title 24 Compliance. The inspection passed, documentation went to the buyer, and the sale closed on schedule.
Book this service →If you are dealing with any of these, a replacement usually costs less over five years than repeated repairs on a dying unit.
Ask a pro →We test the compressor windings, check refrigerant charge, and confirm whether the leak is in the coil or the line set. If the repair cost passes a third of a new system, we quote replacement with a matched condenser and coil so the problem does not come back.
We run a load calculation to confirm the right tonnage, then install a properly sized system. If ductwork is undersized, we address that too. Most homeowners see the runtime stabilize and the bill drop within the first full month.
We replace the system with new equipment running R-410A or R-32 refrigerant, both of which are readily available and efficient. You stop chasing a refrigerant that is being phased out and get a system with a full warranty.
We look at the repair history, the age of the unit, and the condition of the coil and compressor. When the pattern is clear, we quote replacement with honest numbers so you can decide based on total cost, not just this month's bill.
“Our 16-year-old unit died in the middle of a July heat wave. Azusa Breeze came out the same day, ran a load calculation, and had a new Carrier system in by the next afternoon. The house went from 94 degrees to 74 in about two hours. They cleaned up everything and even hauled away the old pad.”
Maria G.Homeowner, North Azusa
✓ Verified“We got three quotes for ac replacement and Azusa Breeze was the only one that actually measured the house instead of guessing tonnage. They found our old system was oversized, which explained the short cycling. New Rheem unit runs quieter and our August bill dropped about $90 compared to last year.”
David R.Homeowner, Azusa Foothills
✓ Verified“Called at 8 p.m. on a Sunday when the AC quit. They answered, walked me through a quick check, and had a tech out Monday morning. Compressor was gone, so we replaced the whole system. Financing made it manageable, and the crew was in and out in one day.”
Priya S.Homeowner, Citrus Avenue Corridor
✓ VerifiedMost full system replacements in azusa run $6,500 to $14,000 in 2026, depending on tonnage, efficiency rating, and whether ductwork needs work. A basic 3-ton 14.3-SEER2 package sits near the low end, while a variable-speed 18-SEER2 heat pump with a new line set and smart thermostat lands at the top. We give you exact numbers after the load calculation, not a phone guess.
A standard residential swap takes one day, usually 6 to 10 hours. If we are also replacing ductwork or adding a zoning system, plan on two days. We start in the morning and have you cooling by late afternoon in most cases. Complex attic runs or hillside properties in the Foothills can push it to a second day.
Replace it if the unit is over 12 years old, uses R-22 refrigerant, or the repair costs more than a third of a new system. Repair makes sense on a 6-year-old unit with a bad capacitor or contactor. We diagnose first, quote both paths, and let the numbers decide. There is no pressure either way.
Yes. We run 24/7 ac replacement azusa California calls, including nights and weekends. If your compressor failed or your system is blowing warm air in a heat wave, call (626) 765-0724. We triage over the phone, and if replacement is the only fix, we schedule the soonest available slot, often within 24 to 48 hours.
Call (626) 765-0724 and we will schedule a same-day estimate for ac replacement in azusa. We show up when we say we will, quote the full job in writing, and stand behind the install with a labor warranty. Cold air is one phone call away.
Get Free Estimate (626) 765-0724 →Call (626) 765-0724 or email info@azusabreezehvac.com and we will get you on the schedule. We answer the phone seven days a week, run emergency calls around the clock, and aim to have a tech at your door the same day for no-cool calls across Azusa and Los Angeles County.