Sealed, balanced, code-correct duct systems built for Southern California homes

Ductwork Installation azusa CA Done Right the First Time

When your ductwork installation azusa CA project needs to be done right, we size, seal, and balance every run so your rooms actually hit the temperature on the thermostat. We handle ductwork repair azusa California calls the same week, from pinhole leaks in the attic to crushed flex runs behind drywall. If your energy bill jumped and one room never cools, your ducts are the likely culprit.

Ductwork Installation & Repair in azusa, California
Careful work. Honest options.
About this service

Ductwork Installation azusa CA Built for Real Airflow

Ductwork installation azusa CA is the design, fabrication, and sealing of the network of supply and return ducts that carries conditioned air from your air handler to every room. We measure static pressure, size each trunk and branch to ACCA Manual D, and seal every joint with mastic and foil tape instead of relying on leaky duct tape. A properly installed system keeps pressure balanced so your blower motor is not fighting itself.

Most azusa homes we open up have the same problem: attic ducts baked by summer heat, disconnected flex runs, and joints that leak 20 to 30 percent of your cooled air before it reaches a register. If you have been searching for duct repair near me azusa, that lost air is why your system runs longer and your bill keeps climbing. We pressure-test, seal, and in many cases rebuild the runs that are too far gone to save.

  • ✓ Lower Cooling Bills
  • ✓ Even Room Temperatures
  • ✓ Cleaner Indoor Air
  • ✓ Longer Equipment Life
What's included

What Our Ductwork Service Includes

Every duct job we run starts with a full inspection and pressure test, and ends with a walkthrough and warranty paperwork. The scope below covers what is standard. If your job needs something outside this list, we quote it separately before we start so there are no surprises.

01
✓

Full Duct Inspection

We inspect every accessible run in the attic, crawlspace, and at each register. Disconnected joints, crushed flex, sagging runs, and pest damage all get documented with photos before we quote anything.

02
✓

Pressure Testing

A duct blaster test measures exactly how much air your system is losing. We run the test before and after the job so you can see the actual improvement in numbers, not just a claim.

03
✓

Duct Sealing

We seal every joint, boot, and plenum connection with mastic and foil tape. No duct tape, which fails within a season in a hot azusa attic. Sealed joints stay sealed.

04
✓

Duct Replacement

Runs that are crushed, disconnected, or too far gone get replaced with properly sized flex or rigid duct, supported every 4 feet and sealed at every connection point.

05
✓

System Balancing

After the runs are in and sealed, we balance the system with dampers so each room gets the airflow it needs. This is what fixes the hot-room, cold-room problem most homeowners call about.

06
✓

Warranty and Documentation

You get the before-and-after pressure readings, a written scope of what we did, and warranty paperwork. If anything we installed does not perform, we come back and make it right.

How it works

Our Ductwork Installation and Repair Process

We start with a full walkthrough of your attic, crawlspace, and every register. A duct blaster and static pressure test show exactly how much air you are losing and where. This usually takes 45 to 90 minutes, and you get the numbers in plain English before we quote anything.

You get a written scope listing every run we will repair or replace, the materials, and a flat price. No hourly surprises. If we find something unexpected once we open a wall, we stop and show you before doing any additional work.

Most single-system duct jobs take one to two days. We lay drop cloths, protect flooring, and keep the work area clean. New runs are fabricated to size, sealed with mastic, and supported every 4 feet so they do not sag and trap air.

After the runs are in, we seal every joint, boot, and plenum connection, then balance the system with dampers so each room gets the airflow it needs. We re-run the static pressure test to confirm we hit target before we call it done.

We walk you through what we did, show you the before-and-after pressure readings, and hand you the warranty paperwork. Our workmanship is warrantied, and we are a phone call away if anything does not perform the way we said it would.

Ductwork Installation & Repair
STEP 01Inspection and Testing

We start with a full walkthrough of your attic, crawlspace, and every register. A duct blaster and static pressure test show exactly how much air you are losing and where. This usually takes 45 to 90 minutes, and you get the numbers in plain English before we quote anything.

Tools & methods

Tools and Methods We Use on Ductwork

01
✓

Duct Blaster

Measures total duct leakage in CFM25 so we can quantify exactly how much air your system is losing before and after the job.

02
✓

Manifold Gauge Set

Checks refrigerant pressures when we suspect duct problems are masking an airflow or charge issue. We test both so we fix the real cause.

03
✓

Micron Gauge and Vacuum Pump

Used when a duct job requires opening the refrigerant circuit. We pull a deep vacuum and verify with a micron gauge before charging.

04
✓

Leak Detector

Finds refrigerant leaks that sometimes get confused with duct problems. If your ducts test clean but cooling is weak, this is the next step.

05
✓

Psychrometer

Measures temperature and humidity at the return and supply so we can calculate actual system performance, not just guess at it.

06
✓

Clamp Meter and Multimeter

Tests blower motor amp draw and control board voltage when duct problems have caused electrical strain on the system.

Real results

Before and after.

1950s Duct Replacement in Downtown Azusa
Ductwork Installation & Repair

1950s Duct Replacement in Downtown Azusa

A 1,400 square foot home near Downtown Azusa had original 1958 ductwork with 32 percent leakage. The back bedroom never cooled below 82 degrees in summer, and the electric bill ran $340 a month.

After: We replaced the failing runs, sealed every joint with mastic, and balanced the system. Duct leakage dropped to 6 percent, the back bedroom now hits 76 degrees, and the summer bill dropped to about $240 a month.

Book this service →
Disconnected Attic Run in Azusa Foothills
Ductwork Installation & Repair

Disconnected Attic Run in Azusa Foothills

A homeowner in the Azusa Foothills had a disconnected flex run dumping cold air into a 145-degree attic. The system ran 14 hours a day and still could not keep up on 100-degree afternoons.

After: We reconnected the run, resealed the collar with mastic, and added proper support every 4 feet. Static pressure dropped from 0.9 to 0.55 inches of water column, and the system now cycles normally even on the hottest days.

Book this service →
Undersized Return Fix in North Azusa
Ductwork Installation & Repair

Undersized Return Fix in North Azusa

A North Azusa home had a return duct that was too small for the 4-ton system, causing the evaporator coil to freeze every few weeks. The homeowner had paid for two refrigerant top-offs before calling us.

After: We measured static pressure, calculated the return size the system actually needed, and added a second return. The coil stopped freezing, the compressor amp draw dropped to spec, and no more refrigerant top-offs were needed.

Book this service →
Problems we solve

Duct Problems We Fix in azusa Homes

Most duct problems show up as comfort complaints or high bills before they show up as a visible failure. These are the four we see most often in azusa attics and crawlspaces.

Ask a pro →
01

Disconnected flex runs dumping cold air into the attic

We reconnect the run, reseal the collar, and support it properly so it does not pull apart again. We pressure-test the system after to confirm the fix.

↗
02

Crushed or kinked ducts behind drywall or under flooring

We locate the restriction with a camera and static pressure readings, then replace the crushed section with properly sized duct and re-test airflow to confirm the fix.

↗
03

Leaky joints and unsealed plenum connections

We seal every joint, boot, and plenum connection with mastic and foil tape, then re-run the duct blaster test to show you the leakage number before and after.

↗
04

Undersized return ducts starving the system

We measure static pressure, calculate the return size the system actually needs, and add or enlarge the return so the equipment gets the airflow it was designed for.

↗
Proof you can check

Licensed, Certified, and Warrantied

  • California Contractor License C-20 (HVAC) · California State License Board
  • EPA Section 608 Universal Certification · U.S. Environmental Protection Agency
  • NATE Certification · North American Technician Excellence
  • ACCA Manual J and Manual D Design · Air Conditioning Contractors of America
  • Title 24 Compliance Verification · California Energy Commission
Customer reviews

What azusa Customers Say About Our Ductwork

★★★★★
“Our back bedroom never cooled and the bill kept climbing. Azusa Breeze HVAC pressure-tested the ducts, found three disconnected runs in the attic, and rebuilt them in one day. The bedroom now hits the setpoint and our summer bill dropped about $80 a month. They showed us the before-and-after readings, which I appreciated.”
MR

Maria R.Homeowner, North Azusa

✓ Verified
★★★★★
“I manage several rental units near Citrus Avenue and duct problems come up constantly. Azusa Breeze HVAC is the only contractor I call now. They show up when they say they will, quote a flat price, and the work passes inspection. Their techs know the older duct layouts in these buildings, which saves a lot of guesswork.”
JK

Jennifer K.Property Manager, Downtown Azusa

✓ Verified
Good questions

Frequently Asked Questions About Ductwork in azusa

(626) 765-0724 →

Most full duct replacements in azusa run $3,500 to $8,500 depending on home size, attic access, and how many runs need to be rebuilt. Partial repairs typically land between $450 and $1,800. We quote a flat price after the inspection, so you know the number before we start cutting.

A single leaky joint or disconnected run takes 2 to 4 hours. A partial system repair with sealing and balancing usually takes one full day. Full duct replacement runs one to two days for most azusa homes, and we tell you the timeline in the written scope before we start.

Three signs show up most often: rooms that never reach the thermostat setting, dust collecting faster than usual, and cooling bills that climb without a rate change. If your attic ducts are more than 15 years old, a duct blaster test will show exactly how much air you are losing.

Yes. If a duct has collapsed, disconnected, or is dumping cold air into your attic during a heat wave, call us at (626) 765-0724 and we will get someone out the same day when slots are open. We keep emergency capacity for no-cool situations, especially in July and August.

Ready when you are

Get Your Ductwork Installation azusa CA Quote Today

Call (626) 765-0724 and we will schedule a duct inspection, pressure-test your system, and give you a flat written price. Licensed, insured, and warrantied work. If your ducts are leaking money into the attic, we will show you exactly where.

Schedule Duct Inspection (626) 765-0724 →
Request an appointment

Contact Azusa Breeze HVAC

Call (626) 765-0724 or email info@azusabreezehvac.com and we will get you on the schedule. We answer the phone seven days a week, run emergency calls around the clock, and aim to have a tech at your door the same day for no-cool calls across Azusa and Los Angeles County.

↗
Emergency?Call now